WindowMizer Read Me
- Downloaded the WindowMizer.dmg file
- Double-click the disk image to display the contents.
- Drag the WindowMizer icon onto the Applications folder icon.
- Remove the WindowMizer disk from the Desktop.
- Launch WindowMizer from the Applications folder on your hard drive.
The first time you launch WindowMizer, you may see the following Gatekeeper warning. If you do not see any Gatekeeper warnings, you can proceed to Step 3.
If you trust the source where you obtained WindowMizer, press the Open button to continue and proceed to Step 3.
If you see the following Gatekeeper alert, dismiss it by pressing the OK button.
You will have to manually approve WindowMizer to be installed on your computer.
To manually approve installation of WindowMizer, right-click (or control+click) on the WindowMizer.app icon and click Open from the popup menu.
You will see another Gatekeeper alert. It is slightly different than the first one. This time there is an Open button.
If you are certain the app is from a trusted source (i.e. downloaded from rgbworld.com, macupdate.com, etc,). Click the Open button.
That completes all Gatekeeper security steps for WindowMizer.
3. ENABLE ACCESSIBILITY:
The first time you run WindowMizer, you will be asked to authorize WindowMizer to communicate with other applications.
3a. ENABLE ACCESSIBILITY (OS 10.9 and Newer):
You will be presented with the following alert. Press the Open System Preferences button to continue.
You will be taken to System Preferences > Security & Privacy preference pane where WindowMizer will be shown in a list of Apps allowed to control your computer. You need to unlock the screen, then enable the checkbox next to WindowMizer. Once completed, you can close System Preferences and relaunch WindowMizer. Note: If WindowMizer is not listed, you can drag-and-drop the app icon into the list.
3b. ENABLE ACCESSIBILITY (OS 10.6 - 10.8.x)
Press the Authorize... button to continue.
Alternately, you can "Enable access for assistive devices" in System Preferences.
Enabling access for assistive devices is less secure than authorizing WindowMizer
because it allows all applications to use Accessibility features.
Pressing the Authorize button will present the Install Helper window shown below. WindowMizer, uses a Helper tool to mark WindowMizer as a trusted application. To allow the Helper to perform the modification, enter your Computer user name and password. Press the Install Helper button to continue.
If the Helper tool is successful, you will see the following message and you can Proceed to Step 4.
If authorization failed or you cancel the operation, you will see the following error alert, and you must "Enable access for assistive devices" in System Preferences or quit and try again.
To manually enable access for assistive devices, go to System Preferences, select the appropriate prefs panel and check the box for Enable access for assistive devices.
• OS 10.6 and 10.7 - System Preferences > Universal Access
• OS 10.8 - System Preferences > Accessibility
After WindowMizer has been trusted OR you have enabled access for assistive devices, you can proceed with Step 3c.
4: RECOMMENDED SYSTEM SETTINGS
The recommended settings are located on a different preference panel depending on the OS version:
• OS 10.6 - System Preferences > Appearance
• OS 10.7 - System Preferences > General
• OS 10.8 - System Preferences > Dock
• OS 10.9 and higher - System Preferences > Dock
5. REGISTERING WINDOWMIZER:
Enter the Activation Code that was emailed to you when you purchased WindowMizer then press the Activate button. The Activation Code is also displayed on your Account > Downloads page when logged into your User Account at rgbworld.com.
After pressing the Activate button, you will will be notified if the app has been activated, or of any problems. If activation was successful, WindowMizer is activated and ready to use.
After pressing the Demo button, you will see the following message allowing you to use WindowMizer for 14-days before purchasing a license. Press the Start Trial button to continue.
After pressing the Start Trial button, you will be alerted to the status of the demo. If you are opening WindowMizer within 14-days of the 1st time you have launched the app, you will see the following message indicating when the trial period will expire.
If the trial period has expired, you will see the following message. Press the Buy Now... button to go to rgbworld.com where you can purchase a license.